Idect x31 user manual

In a home with broadband, every telephone must have a micro-filter connected, not just the one at the telephone point that your modem is connected to. Turn On or Off the Base Screening If the fault persists Colour display digital cordless telephone with name and number phonebook and answering machine for z1i only 34 pages.

Displays when the handset is on a call. Text And Number Entry Text and Number Entry The table below shows you where each letter and punctuation character can be found, by using repeated presses of the alphanumeric keypad. Follow all warnings and instructions marked on the product. Flashes when there is an incoming call. When you purchase iect phone system, all handsets are already registered to your base, so you do not need to register them.

Press the numeric key containing the first letter of the name you want. Follow Steps 1 and 2 in the section of View the Call list. Delete the current message. If you make a mistake, press to delete the last digit. Colour display telephone with name and number phonebook and answering machine and sms messaging 57 pages.

Page 2 Important note- This telephone is not designed for Emergency calls when the main power fails. For Emergency calls you should have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure.

Page 3 Press for intercom calls. PAGE Press for conference calls. Page 5: Table Of Contents Contents What the symbols mean To create a contact in your phonebook Contents To delete contacts in your phonebook Read First before Use To edit contacts in phonebook Choosing a site unit for the base unit To store a last number redial entry and charger pod in phonebook Radio signals between handset Page 6: Read First Before Use Read First Before Use Choosing a site The base unit and charger pod s should be placed on for the base unit level surface, in a position where: and charger pod the mains adapter plug will reach an easily accessible VAC switched mains supply socket - never try to lengthen the mains power cable.

Page 7: Interference Move nearer to the base unit within 20 seconds, until the warning tone stops. Otherwise, your call may be cut off. Connect the mains power lead and the telephone line cord into the base unit.

Plug one end of the telephone line cord into the socket on the back of the base. Push down on the top of the battery B. Lift the battery pack and connect compartment cover located on the its plug to the socket inside the back of the handset and slide the compartment, as shown.

Page Setting Sms ON. Setting SMS. Note: To answer a call when the handset is switched off, you need to switch it back on. Press the button to confirm. Press the button. Press the button to select Alarm. Note: If Auto answer is set then lifting the handset off the base or charger will answer the call and no buttons need to be pressed. To use the characters you press on the button where you see the character, e. Press the button, your phonebook list will appear.

Press the button to select. Page Delivery Receipt Delivery receipt Before sending a message, you can activate the delivery receipt feature that confirms whether or not the message has been sent. Once you have completed your message, press the button. Page Delete A Message Press the button to search your phonebook. Once you have found the name you want to send the message to press the button to select and number of the person would appear.

Press the button for OK. Shortcut to clear phonebook memory Press the button. Press and hold the HASH button for two seconds. Page Set Handset Priority Set Handset Priority If you have more then one handset you can set one handset to ring before the others.

Page Setting Up The Answering Machine Setting up the answering machine Setting the day, clock, number of rings and security remote code If you pause too long between the steps listed below, the machine will time out and you will need to start again. As you press the machine will say the number and the display on the base will also shows it the code has 3 digits, and the default is The X3i has two OGMs and you can record your own message. OGMs that are already on the machine: OGM1- this invites callers to leave a message: 'Sorry, we cannot answer your call now.

When the machine is first switched on, OGM1 is selected, so callers will be able to leave messages. The base unit's display flashes to shows the number of new messages; The machine will tell you the number of messages you have altogether; and then the number of new messages.

Lift the handset of any other phone connected to the same line. Page 49 Remote operation You need to enter a three-digit pass number if you want to dial home to receive your messages.

The original pass-number is Otherwise you are able to set your own three-digit pass number please see page To check your messages remotely Using a tone dialling phone, dial your home number When you hear your outgoing message, press the STAR All connectors are firmly inserted in their sockets. Mains power to the base unit is switched on at the socket.

Page 52 "I cannot make a The handset's keypad may be locked. Unlock it before call. Only one handset or the base unit can be connected to the outside line at once. If another handset is already using the line, you need to wait until it's finished its call.

Page 53 "The Caller Display You need to subscribe to the Caller Display feature from feature isn't your network service provider. You should find contact working. The caller may have withheld their number by dialling Or they may be calling from a network that does not transmit the caller's number e.